Fluke 5020A User Manual Page 111
- Page / 142
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Digital Communications Interface
Commands 6
6-41
Example: SYST:TIME 11,43,28
The <hour>, <minute>, and <second> parameters must all be specified. The <hour>
parameter is a one or two-digit number (0 to 23). The <minute> parameter is a one or
two-digit number (0 to 59). The <second> parameter is a one or two-digit number (0 to
59). This command may be password protected (see Password Commands).
Note
The system time is always set using 24-hour format regardless of the clock
time setting.
SYSTem:TIME:DAYLight? [MIN|MAX|DEF]
Returns the automatic daylight saving adjustment setting.
Example: SYST:TIME:DAYL?
Response: 1
A value of 0 is returned if the daylight saving adjustment is disabled. A value of 1 is
returned if the daylight saving adjustment is set to North America (N AMER). A value of
2 is returned if the daylight saving adjustment is set to Europe (EUROPE). Specifying the
MIN, MAX, or DEF parameter returns the minimum, maximum, or default value
respectively.
SYSTem:TIME:DAYLight <num>|MIN|MAX|DEF
Sets the automatic daylight saving adjustment setting.
Example: SYST:TIME:DAYL 1
The <num> parameter sets the automatic daylight saving adjustment setting to off (0),
North America (1), or Europe (2). This command may be password protected (see
Password Commands).
SYSTem:TIME:FORMat? [MIN|MAX|DEF]
Returns the time format used for the display.
Example: SYST:TIME:FORM?
Response: 1
A value of 0 is returned if the time format is set to 12 hour. A value of 1 is returned if the
time format is set to 24 hour. Specifying the MIN, MAX, or DEF parameter returns the
minimum, maximum, or default value respectively.
SYSTem:TIME:FORMat <num>|MIN|MAX|DEF
Sets the time format.
Example: SYST:TIME:FORM 0
The <num> parameter can be 0 (12 HR) or 1 (24 HR). Specifying the MIN, MAX or
DEF parameter sets the time format to the minimum, maximum, or default value
respectively. This command may be password protected (see Password Commands).
Password Commands
The password commands are used for enabling and disabling the password-protected
commands, for querying and setting the password-protected state, and for setting a new
password. These commands are always password protected.
- Users Manual 1
- Table of Contents 3
- ii 4
- Contents (continued) 5
- iii 5
- iv 6
- List of Tables 7
- vi 8
- List of Figures 9
- viii 10
- Chapter 1 11
- Symbols Used 14
- Safety Information 14
- Safety Information 1 15
- Technical Support 16
- Specifications 17
- Environmental Conditions 18
- Quick Start 19
- Introduction 2 21
- Connect the Power Source 22
- Switch the Power On 22
- Measure Temperature 22
- Parts and Controls 23
- Front Panel 25
- Top Panel 26
- Right Side Panel 26
- Left Side Panel 27
- Back Panel 27
- Quick Buttons 28
- Configurations 28
- Accessories 28
- Accessories 3 29
- General Operation 31
- DC Power Source 33
- Battery 33
- Unit of Temperature 35
- Recording Measurements 35
- Sensors 35
- Menu Functions 37
- Channel Menu 39
- Figure 5-3. Channel Menu 40
- Channel Menu 5 41
- Figure 5-6. Sensor Lock 42
- Display Menu 43
- Figure 5-9. Display Menu 44
- Figure 5-10. Display Setting 44
- Display Menu 5 45
- 5-11 47
- Figure 5-14. Graph Scale 48
- Data Menu 49
- Figure 5-17. Data Record 50
- Data Menu 5 51
- 5-15 51
- 5-17 53
- Figure 5-22. Data Storage 54
- Figure 5-23. Data Clear 54
- 5-19 55
- Figure 5-25. Stats Setting 56
- Figure 5-26. Stats View 56
- 5-21 57
- Figure 5-29. Stats Clear 58
- Figure 5-30. Data Card 58
- 5-23 59
- Alarm Menu 60
- Alarm Menu 5 61
- 5-25 61
- Figure 5-35. Sensor Alarm 62
- System Menu 63
- Figure 5-38. System Menu 64
- Figure 5-39. System Setting 64
- System Menu 5 65
- 5-29 65
- 5-31 67
- Figure 5-43. IR 68
- 5-33 69
- Figure 5-45. System Info 70
- Chapter 6 71
- Communications 73
- Interface Commands 74
- Interface Commands 6 75
- 6-11 81
- Commands 82
- 6-13 83
- 6-15 85
- 6-17 87
- 6-19 89
- 6-21 91
- 6-23 93
- 6-25 95
- 6-27 97
- 6-29 99
- Commands 6 101
- 6-31 101
- 6-33 103
- 6-35 105
- 6-37 107
- 6-39 109
- 6-41 111
- 6-43 113
- 6-45 115
- 6-47 117
- 6-49 119
- 6-51 121
- 6-53 123
- Calibration Procedure 125
- Introduction 127
- Equipment 127
- Preparation 127
- Calibration Points 127
- TSLTSLLTS ∆+= 129
- Chapter 8 131
- Maintenance 133
- Troubleshooting 133
- Downloading Recorded Data 135
- CE Comments 136
- Frequently Asked Questions 136
- Index (continued) 141
Related products and manuals for Measuring, testing & control Fluke 5020A
(24 pages)© 2020, manymanuals.com. All rights reserved. | 0.701 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals