Fluke 8842a User Manual Page 141
- Page / 269
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
8842A
Instruction Manual
6-4
AC Calibrator Fluke 5700A and Fluke 5725A
Minimum Required Accuracy (By Range)
Frequency Range 1, 10, 100 mV
1
1, 10, 100V
2
1000V
2
20 Hz – 30 Hz .1 + .005 .1 + .005 .12 + .005
30 Hz – 20 kHz .02 + 10 0.2 + .002 .04 + .004
20 kHz – 50 kHz .05 + 20 .05 + .005 .08 + .005
50 kHz – 100 kHz .05 + 20 .05 + .005 .1 + .01
1. ±(% of setting + µV) 2. +/-(% of setting + % of range)
AC Current Source Fluke 5700A
Frequency Range Minimum Required Accuracy (All Ranges)
30 Hz – 1 kHz ±.07% + 1 mA)
1kHz – 5 kHz ±(.07% + 1 mA) X frequency in kHz
Shorting Bar Resistance <1.5 mΩ
Construction Soldered (not
rivetted)
Pomona MDP-S-0
6-Inch Jumper ---- E-Z-Hook 204-6W-S or equivalent
Optional Test
Equipment
9010A, 9005A or Micro-System Troubleshooter; 9000A-8048 Interface Pod.
6-2. PERFORMANCE TEST
This test compares the performance of the 8842A with the specifications given in Section
1. The test is recommended as an acceptance test when the instrument is first received,
and as a verification test after performing the calibration procedure. If the instrument
does not meet the performance test, calibration or repair is needed.
To ensure optimum performance, the test must be performed at an ambient temperature
of 18°C to 28°C, with a relative humidity of less than 75%. Also, the 8842A should be
allowed to warm up for one hour prior to beginning any test other than the self-test.
6-3. Diagnostic Self-Tests
The diagnostic self-tests check the analog and digital circuitry in the 8842A. There are 21
analog tests followed by in-guard program memory, calibration memory, and display
tests. Out-guard program memory is tested when self-test is initiated by a remote
command. Microcomputer RAM tests are done only at powerup. Each test is described
in detail under the heading Troubleshooting. All five digital tests are performed at
powerup.
NOTE
The inputs must be left open-circuited while the self-tests are performed.
Otherwise, the 8842A may indicate errors are present. Errors may also be
caused by inductive or capacitive pick-up from long test leads.
If the FRONT/REAR switch is in the REAR position, the 8842A skips tests 3
and 4. Also, if Option -09 is not installed, the 8842A skips tests 1, 2, and 3.
- Instruction Manual 1
- Table of Contents 3
- List of Tables 9
- List of Figures 11
- Contents 13
- Chapter 1 15
- 1-1. INTRODUCTION 16
- 1-3. OPTIONS AND ACCESSORIES 16
- 1-4. SPECIFICATIONS 17
- SPECIFICATIONS 19
- Operating Instructions 26
- 2-1. INTRODUCTION 27
- 2-2. INSTALLATION 27
- 2-5. Adjusting the Handle 28
- 2-6. Rack Mounting Kits 28
- 2-7. OPERATING FEATURES 29
- OPERATING FEATURES 30
- Function 31
- 2-10. Display Features 33
- 2-11. Error Messages 33
- 2-12. Overrange Indication 35
- 2-13. Diagnostic Self-Tests 35
- 2-14. Ranging 35
- 2-15. AUTORANGE 35
- 2-16. MANUAL RANGE 36
- 2-17. Triggering 36
- 2-19. EXTERNAL TRIGGER MODE 36
- 2-24. MAKING MEASUREMENTS 38
- 2-29. Offset Measurements 39
- 2-30. EXTERNAL CLEANING 40
- Remote Programming 42
- 3-1. INTRODUCTION 44
- 3-2. CAPABILITIES 44
- 3-3. BUS SET-UP PROCEDURE 44
- 3-5. A NOTE ABOUT EXAMPLES 47
- B1 Offset On 48
- PUT COMMAND FORMAT 49
- N <value> P0 49
- 3-7. Bn (Offset Commands) 50
- 3-9. Dn (Display Commands) 50
- 3-10. Fn (Function Commands) 51
- 3-11. Get Commands 51
- gain calibration 52
- 3-13. G1 (Get SRQ Mask) 53
- DEVICE-DEPENDENT COMMAND SET 54
- 3-17. G5 (Get IAB Status) 55
- 3-18. G6 (Get YW Status) 55
- 3-19. G7 (Get Error Status) 55
- 3-22. Put Commands 56
- 3-24. P1 (Put SRQ Mask) 57
- 3-27. Rn (Range Commands) 58
- 3-32. Yn (Suffix Commands) 60
- 3-33. Z0 (Self-Test Command) 60
- 3-36. INPUT SYNTAX 61
- 3-37. Definitions 62
- 3-38. Input Processing 62
- 200 PRINT @3, "F4" 64
- 300 INPUT @3, A 64
- 200 INPUT @3, A 65
- 300 PRINT @3, "F4" 65
- 200 INPUT @3, A 65
- 3-42. Types of Output Data 66
- 3-44. MEASUREMENT DATA 66
- 3-45. OVERRANGE INDICATION 67
- 3-46. ERROR MESSAGES 67
- 3-47. Status Data 67
- 3-48. Output Priority 67
- 3-49. SERVICE REQUESTS 68
- 3-51. The SRQ Mask 69
- 3-52. INTERFACE MESSAGES 70
- 3-56. TALK-ONLY MODE 71
- 3-57. REMOTE CALIBRATION 72
- 3-58. TIMING CONSIDERATIONS 72
- 3-59. IMMEDIATE MODE COMMANDS 72
- 3-60. EXAMPLE PROGRAMS 73
- EXAMPLE PROGRAMS 74
- (interface clear) 91
- 4-1. INTRODUCTION 93
- 4-2. DC VOLTAGE MEASUREMENT 93
- DC VOLTAGE MEASUREMENT 94
- 4-5. RESISTANCE MEASUREMENT 95
- 4-8. 4-Wire Ohms 96
- 4-10. TESTING DIODES 98
- 4-13. DC CURRENT MEASUREMENT 99
- Measurement Tutorial 100
- REDUCING THERMAL VOLTAGES 100
- 4-16. True RMS Measurement 101
- 4-17. Waveform Comparison 101
- 4-18. Crest Factor 103
- 4-21. Bandwidth 104
- 4-22. Zero-Input VAC Error 104
- MEASUREMENTS 106
- Theory of Operation 108
- 5-1. INTRODUCTION 110
- 5-4. DC SCALING 111
- DC SCALING 112
- 5-5. VDC Scaling 113
- 5-6. VDC Protection 114
- 5-7. mA DC Scaling 114
- 5-8. Analog Filter 114
- 5-9. TRACK/HOLD CIRCUIT 115
- TRACK/HOLD CIRCUIT 116
- 5-10. Track Configuration 117
- 5-11. Settling Configuration 118
- 5-12. Hold Configuration 118
- 5-15. OHMS CURRENT SOURCE 119
- 5-16. OHMS PROTECTION 120
- 5-17. OHMS FUNCTIONS 120
- 5-20. A/D CONVERTER 122
- 5-21. Timing/Data Control 124
- 5-22. Precision DAC 124
- 5-25. DISPLAY 125
- 5-26. KEYBOARD 126
- 5-27. DIGITAL CONTROLLER 126
- 5-28. In-Guard Microcomputer 128
- 5-31. Calibration Correction 130
- 5-35. GUARD CROSSING 131
- 5-36. POWER SUPPLY 132
- 5-38. Out-Guard Microcomputer 133
- 5-39. Guard Crossing 133
- 5-41. Signal Conditioning 134
- 5-44. VAC Scaling 134
- 5-45. mA AC Scaling 135
- A Message From 136
- PORTIONS REPRINTED 137
- Maintenance 138
- 6-1. INTRODUCTION 140
- 6-2. PERFORMANCE TEST 141
- local control 142
- PERFORMANCE TEST 144
- 6-6. Resistance Test 145
- 2 = 4 ½ digit counts 146
- 6-9. CALIBRATION 147
- 6-11. INITIAL PROCEDURE 148
- • Autoranging 149
- CALIBRATION 150
- 6-18. VERIFYING CALIBRATION 154
- 6-20. TOLERANCE CHECK 155
- 6-23. Remote Calibration 157
- 6-24. TIMING CONSIDERATIONS 160
- 6-25. REMOTE ERASURE 161
- 6-27. DISASSEMBLY PROCEDURE 162
- 6-28. Case Removal 163
- DISASSEMBLY PROCEDURE 164
- 6-31. Main PCA Removal 167
- 6-33. REASSEMBLY PROCEDURE 169
- REASSEMBLY PROCEDURE 170
- 05 Only) 173
- 6-36. TROUBLESHOOTING 173
- TROUBLESHOOTING 174
- 6-38. Diagnostic Self-Tests 178
- 6-39. Self-Test Descriptions 179
- 6-48. DISPLAY SYSTEM 185
- 6-59. ANALOG CONTROL SIGNALS 188
- 00000 11111 000000 000000 0 1 191
- 6-69. SERVICE POSITION 201
- 6-70. DIAGNOSTIC PROGRAM 201
- 6-72. SERVICE POSITION 203
- 6-73. MAJOR PROBLEMS 204
- 6-74. MORE OBSCURE PROBLEMS 206
- 6-76. INTERNAL CLEANING 207
- INTERNAL CLEANING 208
- List of Replaceable Parts 210
- 7-1. INTRODUCTION 212
- 7-2. HOW TO OBTAIN PARTS 212
- 7-4. NEWER INSTRUMENTS 213
- 7-5. SERVICE CENTERS 213
- SERVICE CENTERS 214
- Options and Accessories 230
- 8-1. INTRODUCTION 232
- 8-2. ACCESSORIES 233
- 8-10. Current Shunt (80J-10) 234
- Option –05 IEEE-488 Interface 236
- 805-3. EXTERNAL CONTROLS 238
- 805-4. INSTALLATION 238
- 805-1. INTRODUCTION 238
- 805-2. CAPABILITIES 238
- 805-6. MAINTENANCE 239
- LIST OF REPLACEABLE PARTS 240
- Option –09 True RMS AC 244
- 809-1. INTRODUCTION 246
- 809-2. INSTALLATION 246
- 809-3. OPERATING INSTRUCTIONS 247
- 809-4. MAINTENANCE 247
- Schematic Diagrams 252
Related products and manuals for Unknown Fluke 8842a
Unknown Fluke Weather Radio 79 User Manual
(37 pages)
(37 pages)
Unknown Fluke 8922A User Manual
(124 pages)
(124 pages)
Unknown Fluke 8840A User Manual
(180 pages)
(180 pages)
Unknown Fluke 8920A User Manual
(132 pages)
(132 pages)
Unknown Fluke 4270A User Manual
(184 pages)
(184 pages)
Unknown Fluke 1920A User Manual
(18 pages)
(18 pages)
Unknown Fluke SIGMAPACE 1000 User Manual
(2 pages)
(2 pages)
Unknown Fluke 1060AM-NM-LRVAR User Manual
(16 pages)
(16 pages)
Unknown Fluke 341A User Manual
(98 pages)
(98 pages)
Unknown Fluke Thermometer 2166A User Manual
(18 pages)
(18 pages)
Unknown Fluke 8600A User Manual
(108 pages)
(108 pages)
Unknown Fluke Thermometer 80T-IR User Manual
(10 pages)
(10 pages)
Unknown Fluke 410B User Manual
(54 pages)
(54 pages)
Unknown Fluke 53 Series User Manual
(25 pages)
(25 pages)
Unknown Fluke 8505A User Manual
(70 pages)
(70 pages)
Unknown Fluke MP3 User Manual
(106 pages)
(106 pages)
Unknown Fluke Switch 2205A User Manual
(154 pages)
(154 pages)
Unknown Fluke 9150 User Manual
(49 pages)
(49 pages)
© 2020, manymanuals.com. All rights reserved. | 0.142 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals