Fluke NetDAQ 2645A User Manual Page 206
- Page / 353
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
2640A/2645A NetDAQ
Users Manual
6-34
ds308s.bmp
Apply Displays the suggested value to apply to the instrument from the calibrator.
Actual Enter the actual value applied to the instrument from the calibrator. Use a
value as close as possible to the suggested value for best calibration results.
Perform Calibration Step Apply the calibrator output to the instrument and then
click this button to perform the calibration.
Variations in the Display 6-37.
Under normal operation, the display presents various combinations of brightly and
dimly lit annunciators and digits. However, you may encounter other, random
irregularities across different areas of the display under the following
circumstances:
• After prolonged periods of displaying the same information.
• The display has not been used for a prolonged period
This phenomenon can be cleared by activating the entire display and leaving it on
overnight (or at least for several hours). Use the following procedure to keep the
display fully lit:
1. Turn the instrument power off.
2. Press the front panel
key and then apply power. Continue to hold the
key until the instrument beeps. The entire front panel display comes on
and stays on.
3. When you wish to return the display to normal, press any front panel key.
Service 6-38.
If the instrument fails to operate, check that operating instructions presented
earlier in this manual are being followed. If the problem cannot be remedied, send
the instrument, postage paid, to the nearest Fluke Service Center. A list of Service
- 2640A/2645A 1
- PCaution 4
- SAFETY TERMS IN THIS MANUAL 5
- Table of Contents 7
- 2640A/2645A NetDAQ 10
- Contents 11
- List of Tables 13
- List of Figures 15
- Overview 17
- Introduction 1-1 19
- Analog Channels 1-3 23
- Computed Channels 1-4 23
- Channel Numbering 1-5 23
- Mx+B Scaling 1-6 23
- Alarms 1-7 24
- Channel Monitoring 1-8 24
- Digital I/O 1-9 24
- Totalizer 1-10 24
- Trigger Input 1-11 25
- Trigger Output 1-12 25
- Alarm Trigger 1-16 26
- Master Alarm 1-13 26
- Interval Trigger 1-14 26
- External Trigger 1-15 26
- Isolated Networks 1-19 28
- General Networks 1-20 28
- Ethernet Port Selection 1-21 28
- Scanning and Logging 1-24 29
- RS-232 Interface 1-25 29
- Options and Accessories 1-27 30
- Options and Accessories 31
- Preparing for Operation 33
- Introduction 2-1 35
- Instrument Preparation 2-2 35
- Instrument Preparation 37
- PWarning 38
- Trigger Input 2-16 45
- Trigger Output 2-17 46
- Master Alarm 2-18 46
- Controls and Indicators 2-20 47
- Front Panel Controls 2-21 49
- Front Panel Indicators 2-22 50
- Rear Panel Controls 2-23 52
- Rear Panel Indicators 2-24 52
- Power-On Options 2-26 53
- Testing and Troubleshooting 87
- Configuring NetDAQ Logger for 95
- Introduction 3-1 97
- Configuring the Current Setup 101
- Setup Files 3-14 105
- Opening a Setup File 3-16 106
- Setup Files 107
- Configuring an Instrument 109
- Configuring Channels 3-23 112
- Configuring Channels 113
- Equation Syntax 3-28 115
- Configuring Alarms 3-30 117
- Operating NetDAQ Logger for 125
- Introduction 4-1 127
- Simulated Logging 4-6 129
- Real-Time Displays 4-8 130
- Real-Time Displays 131
- The Spy Window 4-11 133
- Quick Plot 4-12 135
- Data Files 4-14 137
- Configuring a Data File 4-15 138
- Data Files 139
- Converting Data Files 4-16 142
- Optimizing Performance 143
- Optimizing Performance 4-18 144
- Using Online Help 4-24 145
- Using Trend Link for Fluke 147
- Introduction 5-1 149
- Introduction 151
- Curve Preferences 5-21 164
- Background Preferences 5-22 167
- Using the Note System 5-25 170
- Printing a Chart 5-26 170
- Click OK to print the chart 172
- Maintenance 173
- Introduction 6-1 175
- Cleaning 6-3 176
- Fuse Replacement 6-4 176
- Fuse (15/100A, 250V 177
- Time Delay) 177
- Performance Test 6-5 178
- Performance Test 179
- Volts AC Accuracy Test 6-11 185
- Frequency Accuracy Test 6-12 186
- 5. Close Spy Window 191
- Step 2) 194
- Digital I/O Output Test 6-25 198
- Digital Input Test 6-26 199
- Totalizer Tests 6-27 200
- Totalizer Count Test 6-28 200
- Trigger Input Test 6-31 202
- Trigger Output Test 6-32 202
- Calibration 6-33 203
- Calibration 205
- Service 6-38 206
- Replacement Parts 6-39 208
- Appendices 209
- Introduction A-1 211
- Digital I/O A-6 214
- Trigger In A-7 215
- Trigger Out A-8 216
- Master Alarm A-9 216
- 2640A Specifications A-12 217
- Specifications 219
- 2645A Specifications A-21 227
- Introduction B-1 237
- Noise and Shielding B-3 237
- Crosstalk Considerations B-4 238
- Crosstalk Considerations 239
- Introduction C-1 241
- True-RMS Measurements 243
- Introduction D-1 245
- Fixed-385 RTD D-2 245
- Custom-385 RTD D-3 246
- RTD Linearization 247
- Introduction E-1 251
- Introduction F-1 253
- File Format F-2 253
- Introduction G-1 255
- DDE Links Reference G-2 255
- DDE Example Using Excel G-3 256
- Dynamic Data Exchange (DDE) 257
- Introduction H-1 261
- UTP Cables H-2 261
- Introduction I-1 263
- Network Primer I-4 265
- Network Considerations 267
- Drivers I-10 271
- TCP/IP Protocol Stack I-11 273
- Glossary I-24 293
- Introduction J-1 299
- Full-Disk J-3 299
- Scan Queue Overflows J-4 299
- Error Conditions J-5 299
- Error and Status Messages 301
- Instrument not found! 315
- Not responding to command! 321
- Performing Rollover 322
- Unable to Open Mx+B File! 329
- Unable to open RS232 port! 329
- Unable to Open Setup File! 330
- Unable to stop scanning! 330
- Unknown Communication Error! 331
- Window creation failed! 332
- Winsock.dll not found! 332
- Fluke Service Centers 333
- (continued) 341
Related products and manuals for Hardware Fluke NetDAQ 2645A
(74 pages)© 2020, manymanuals.com. All rights reserved. | 6.616 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals