®PN 2063508January 2003© 2003 Fluke Corporation. All rights reserved. Printed in China.All product names are trademarks of their respective companies.
12 MultimeterMEASURING VOLTAGE7MEASURING VOLTAGE1. Insert the test leads in the jacks.2. To select a voltage function, put the slide-switch in the m
12 MultimeterUsers Manual8Figure 3. Measuring Voltage
12 MultimeterTESTING CONTINUITY AND MEASURING RESISTANCE9TESTING CONTINUITY AND MEASURING RESISTANCE1. Insert the test leads in the jacks, and turn o
12 MultimeterUsers Manual10Figure 4. Continuity and Resistance Measurements
12 MultimeterTESTING DIODES11TESTING DIODES1. Insert the test leads in the jacks.2. Put the slide-switch in the continuity/ohms position. The meter
12 MultimeterUsers Manual12Figure 5. Testing Diodes
12 MultimeterVCHEK AND HOW TO USE IT13VCHEK AND HOW TO USE ITi is a subset of the continuity/ohms function. In i, the meter is designed toautomaticall
12 MultimeterUsers Manual14Use i only on power supplies and other power sources that have a low outputimpedance. Do not use i to measure voltage in el
12 MultimeterMEASURING CAPACITANCE15MEASURING CAPACITANCEFirst, turn off power to the circuit, and disconnect and discharge the capacitor.1. Insert t
12 MultimeterUsers Manual16Figure 6. Measuring Capacitance
iTable of ContentsTitle PageREAD FIRST: SAFETY INFORMATION... 1SYMBOLS...
12 MultimeterUSING MIN MAX FUNCTIONS17USING MIN MAX FUNCTIONSRecording Minimum and Maximum ReadingsMIN MAX records the highest and lowest measurements
12 MultimeterUsers Manual18Figure 7. Displaying Minimum and Maximum Reading
12 MultimeterUSING MIN MAX FUNCTIONS19Recording Minimum and Maximum Reading with Elapsed TimeThe MIN MAX with elapsed-time mode records the time (in h
12 MultimeterUsers Manual20Figure 8. Maximum and Minimum Reading with Elapsed Time
12 MultimeterUSING MIN MAX FUNCTIONS21Capturing Continuity Intermittents with Continuity CaptureWhen testing continuity, the meter can capture intermi
12 MultimeterUsers Manual22Figure 9. Open-to-Short and Short-to-Open Transitions
12 MultimeterTURNING BEEPER OFF23TURNING BEEPER OFFTo disable all beeper functions, press and hold down [Z] for 2 seconds while turningthe meter on.MA
12 MultimeterUsers Manual24Service and PartsThis meter should be serviced only by a qualified service technician. To order theservice manual (PN 90082
12 MultimeterSPECIFICATIONS25Maximum Voltage Between anyTerminal and Earth Ground 600 V rmsDisplay 3 3/4-digits, 4000 counts, updates 4/secOperating T
12 MultimeterUsers Manual26Function Range Resolution Accuracy (50 to 400 Hz)4000 mV* 1 mV ±(1.9 %+3)4.000 V 0.001 V ±(1.9 %+3)40.00 V 0.01 V ±(1.9 %+3
12 MultimeterUsers ManualiiRecording Minimum and Maximum Reading with Elapsed Time... 19Capturing Continuity Intermittents with Continuity Ca
12 MultimeterSPECIFICATIONS27Function OverloadProtection*InputImpedance(Nominal)Common ModeRejection Ratio(1 kΩ Unbalance)Normal ModeRejection600 V dc
12 MultimeterUsers Manual28
1READ FIRST: SAFETY INFORMATIONThis meter has been designed and tested in accordance with IEC Publication 1010. Toensure that the meter is used safely
12 MultimeterUsers Manual2SYMBOLSThe following international electrical symbols are used in this manual:W Important Safety Information in Manual∅ Not
12 MultimeterDISPLAY3DISPLAYFigure 1. Display
12 MultimeterUsers Manual4OPERATING FEATURESFigure 2. Operating Features
12 MultimeterSTANDBY MODE5STANDBY MODEIn standby mode, the display goes blank to preserve battery life. The meter beeps andenters Standby if it is ON
12 MultimeterUsers Manual6AutorangingThe meter defaults to autorange when you turn it on. In autorange, the meter selectsthe range automatically.Manua
Comments to this Manuals